Vehicle repair (32)

• For emergency starting
• For intensive professional use
• Ideal for cars, vans, trucks, boats, vehicles agricultural, generators etc.
• Voltmeter to indicate the charge status of the internal battery
• Rear connector for voltage selection
• External fuse: overcurrent protection up to 300A
• Shockproof ABS shell
• Overvoltage protection
• Also suitable for sealed batteries
• Inclined clamps
• Supplied with mains charger

• For the extraction of lubricating oil from engine, brakes, gearbox and antifreeze fluids from any type of vehicle (no hydrocarbons)
• It allows a fast and easy replacement of brake fluid on the vehicle directly
• Use: manually using a lever or pneumatic with compressed air
• Compact dimensions and light weight to be used in many sectors: Automotive, Industrial, Marine and Aeronautical
• It allows fast and safe operations even outside the workshop
• Tank and polypropylene structure for high resistance to oils
• Vacuum valve located on the upper side
• Possibility to check the amount of fluid extracted by side marker
• The vacuum inside the tank decreases when the maximum level is reached
• Integrated carrying handle
• Supplied with 4 suction tubes with different diameters and lengths 400xØ 9,5 mm, 700xØ 6 mm, 850xØ 7 mm, 700xØ 6 mm
• Equipped with tube long 150 cm, Ø 16 mm, for the coupling of 4 suction tubes
• Supplied with instruction manual
• Spare tube, long 150 cm Ø 16 mm: code 1004730-69
• Spare tube, long 400 mm Ø 9,5 mm: code 1004730-65
• Spare tube blue, long 700 mm Ø 6 mm: code 1004730-66
• Spare tube black, long 850 mm Ø 7 mm: code 1004730-67
• Spare nylon tube long 700 mm Ø 6 mm: code 1004730-68

• Complete kit for the most part of vehicles
• Magnetic sockets to hold plugs
• 3/8" hinged wrench for exceptional accessibility
• Protection cup to keep hands clean and prevent contact with oil and hydrocarbons
• Supplied with working support with fixing clip to be secured on the arm of oil trays
• Contents:

  - 1 hinged wrench 3/8” 
  - 2 bits 8-10 mm 3/8"
  - 6 bits 8-10-12-13-14-17 mm 3/8"
  - 6 hexagonal sockets 13-14-17-18-19-21 mm  3/8"
  - 1 TORX® bit T45

• Integrated die-cast steel ring on the end of the socket for superior strength compared to standard wheel nut sockets
• Teflon protection that reduces the risk of damaging alloy rims

• To bleed fluid for hydraulic brakes and clutches
• Working pressure 6÷10 bar
• Tank capacity 3 litres
• Air connection 1/4
• Equipped with pressure gauge (with rubber protection) that shows the vacuum value
• Suction rubber tube with Ø 0,9 cm and total length 105 cm (7 cm of the connector included)

• For changing, filling and bleeding the circuit of brakes on cars and industrial vehicles
• Device designed exclusively for brake fluids DOT 3, DOT 4, DOT 5.1. No LHM.
• Adjustable pressure up to 4 bar
• Automatic stop at 10% of the tank (1 L)
• Power supply 12 V  with crocodile clips
• Rear accessory housing
• Integrated wheels and handle for easy transport
• Operating liquid system: peristaltic pump (no direct pump/liquid contact, no air pressure on liquid)
• Supplied with spare gaskets, 1 multi-diameter cap 44-45-46 mm (U28470107Q) and tank for oil recovery

• Automatic belt clamping
• Lever to increase clamping power for perfect grip on the filter
• Articulated jaws for gripping the filter and having a ratchet effect
• Stainless steel strap
• Handle (160 mm) in high resistant plastic material (hydrocarbons, bumps)
• Capacity: Ø 66÷105 mm

• Allows the re-tightening at the original torque (value indicated on the plastic cap)
• 3/8" square drive
• Steel body
• Set for Fiat, Lancia, Alfa Romeo, BMW, Renault, Volkswagen, Skoda, Audi, Seat, Mercedes
• Profile dimensions: Ø 76 mm x 14 sides - Ø 76 mm x 16 sides - Ø 88 mm x 16 sides - Ø 102 mm x 14 sides - Ø 66 mm x 18 sides - Ø 96 mm x 18 sides 

• Specific for removing the oil filter covers on Toyota, Lexus, Daihatsu, Subaru engines
• Can also be used to remove the Toyota oil filter cartridge
• Reduces the risk of damage to the oil filter covers
• 3/8" square drive; 27 mm hexagon
• Can also be used for tightening with a torque wrench
• Body in phosphatized Aluminum

           446 DT1
           Profile dimensions: Ø 64,5 mm x 14 sides
           Overall dimensions: (Øxh):  80x49 mm 
           446 DT2
           Profile dimensions:  Ø 64,5 mm x 14 sides
           Overall dimensions: (Øxh):  86x49 mm

• For petrol and diesel vehicles
• Ergonomic bimaterial handgrip

• Three-axial heads to work in any position
• To open and close CLICK spring-clips on fuel circuits, intake manifolds and hydraulic circuits
• Steel body, phospatized finish
• Ergononomic bimaterial handgrip

• Allows testing of the battery health, starting system, and charging system
• Usable with 12V batteries, with capacity 100-2000 CCA, BCI, CA, MCA, IT, SAE; 100-1400 DIN, IEC; JIS 26A17-245H2
• Enables testing of standard (Lead-acid),GEL, EFB, Flat AGM, Spiral AGM, Lithium batteries
• Backlit screen
• Cable length (including clamps): 94 cm
• Reverse polarity protection
• 8 selectable languages: Italian, English, German, French, Dutch, Russian, Spanish, and Portuguese
• Battery can be tested both onboard and off the vehicle
• The tester provides 99.5% accurate results

• Automatic cable rewind model with locking device
• Shockproof plastic body with swivel bracket for wall mounting
• 3G x 1.5mm² PVC cable
• Schuko plug and socket
• Rack cable locking device engageable every 50 cm

• White/red striped polypropylene tape, 20 m length
• For creating temporary barriers and marking hazardous areas
• Automatic tape rewind model with locking device
• Shockproof plastic body with swivel bracket for wall mounting
• 180° adjustable bracket
• Tape width 4 cm

• Ideal for gripping pieces and parts difficult to reach
• Pointed jaws with knurled gripping surface
• Up to 70% longer than normal long nose pliers
• Small size double joint for maximum accessibility
• Handles covered in anti-slip material

• Integrated die-cast steel ring on the end of the socket for superior strength compared to standard wheel nut sockets
• Teflon protection that reduces the risk of damaging alloy rims
• Compact plastic container
• Metal latch clip
• Empty case code: U02700106Q

• To extract mouldings, fasteners, trim clips from door panels and dashboards
• No damages to plastic parts, gaskets, body

• For removal of counterweights, silicone, plastics, mouldings etc.
• No damage to parts in plastics, gaskets and ceramics
• Can be used with a hammer
• Regrindable with a file
• Length 270 mm
• Blades width 19-22-25-38mm

• For assembly and disassembly of injectors pipes fittings
• Bihexagonal openings
• Length: 98 mm
• Square drive 1/2"
• Sizes: 12-14-16-17-18-19 mm
• Special steel
• Chrome plated
• Supplied in plastic box